SAE ARP1179 Aircraft Gas Turbine Engine Exhaust Smoke Measurement

作者:标准资料网 时间:2024-05-11 05:26:21   浏览:8628   来源:标准资料网
下载地址: 点击此处下载
Product Code:SAE ARP1179
Title:Aircraft Gas Turbine Engine Exhaust Smoke Measurement
Issuing Committee:E-31 Aircraft Exhaust Emissions Measurement Committee
Scope: This Aerospace Recommended Practice (ARP) standardizes test equipment and procedures for the measurement of smoke emission from aircraft gas turbine engines. The procedures included are for determining and reporting the amount of smoke emission. Tests have indicated that the practically achievable precision of the smoke number is within 卤3 when the system is properly used as outlined herein. This procedure is not intended for in-flight testing, nor does it apply to afterburning mode.
下载地址: 点击此处下载
【英文标准名称】:Threephaseoil-immerseddistributiontransformers50Hz,from50to2500kVAwithhighestvoltageforequipmentnotexcceeding36kV-Part6:Requirementsandtestsconcerningpressurisedcorrugatedtanks;GermanversionHD428.6S1:2002
【原文标准名称】:最高电压不超过36Kv的设备用50Hz、50至2500kVA的三相油浸式配电变压器.第6部分:有关增压式波形槽的要求和试验;德文版本HD428.6S1:2002
【标准号】:DIN42500-6-2003
【标准状态】:作废
【国别】:德国
【发布日期】:2003-01
【实施或试行日期】:
【发布单位】:德国标准化学会(DIN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:变压器;规范(验收);试验;尺寸选定;设备;配电变压器;电压;三相电流;油;验证;油浸式变压器;抗压应力;测量;槽
【英文主题词】:Compressionstresses;Dimensioning;Distributiontransformers;Equipment;Measurement;Oil-immersedtransformers;Oils;Specification(approval);Tanks;Testing;Three-phasecurrent;Transformers;Verification;Voltage
【摘要】:ThispartofHD428seriesisapplicabletotestprocedurestoverifythemechanicalwithstandcapabilityofthecorrugatedtanksofcompletelyoilfilledandhermeticallysealeddistributiontransformers.
【中国标准分类号】:K41
【国际标准分类号】:29_180
【页数】:6P;A4
【正文语种】:德语


【英文标准名称】:Boringbars(toolholderswithcylindricalshank)forindexableinserts--Designation
【原文标准名称】:转位刀片用镗杆(圆柱柄刀具架).标识
【标准号】:JISB4128-1998
【标准状态】:现行
【国别】:日本
【发布日期】:1998-08-20
【实施或试行日期】:
【发布单位】:日本工业标准调查会(JP-JISC)
【起草单位】:TechnicalCommitteeonMachineElements
【标准类型】:()
【标准水平】:()
【中文主题词】:刀具夹持装置;刀具柄;切削工具;作标记;镶齿;可转位刀片
【英文主题词】:tool-holdingdevices;toolshanks;indexableinserts;inserts(cuttingtools);cuttingtools;marking
【摘要】:この規格は,スローアウェイ(刃先交換)チップ(以下,チップという。)を保持する,円形断面のシャンクをもつスローアウェイチップ用ホルダ(以下,ホルダという。)の呼び記号の付け方について規定する。
【中国标准分类号】:J41
【国际标准分类号】:25_100_10
【页数】:10P;A4
【正文语种】:日语